Load Failure

[Former Member]

Hi All,

I run process chain for master and transaction data on daily basis through process chain,now all my chains are getting failed and ginving me the following error message,

For master data process chain am getting the below error message

Diagnosis

In the source system, there is no transfer structure available for

InfoSource 0MATERIAL_TEXT .

System Response

The data transfer is terminated.

Procedure

In the Administrator Workbench, regenerate from this source system the

transfer structure for InfoSource 0MATERIAL_TEXT .

For transcation data process chain

ABAP/4 processor: MESSAGE_TYPE_X A 00 671

Kindly suggest me on this issue..!!

Thanks in Advance

[Former Member · Accepted solution]

For master data process chain, in AWB go to Source system, select the source system from where you pull the data, right click and replicate datasources.

After you do this, the master data process chain must run properly.

Thanks

Archana

[Former Member · Accepted solution]

Hi Archana & YJV,

Hi,

Infact i tried all this procedures but still my load getting failed.Replicated datasources also done source system restore.am getting the below error message.

Check Load from InfoSource

Error message from the source system

Diagnosis

An error occurred in the source system.

System Response

Caller 09 contains an error message.

Further analysis:

The error occurred in Service API .

Refer to the error message.

Procedure

How you remove the error depends on the error message.

Note

If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request.

Kindly suggest me.

Thanks

[Former Member · Accepted solution]

You can try this Solution

Go to transaction SE38,

RS_TRANSTRU_ACTIVATE_ALL and click on execute .

Give your source system and Infosource name and click on execute .

Then master data again and see.

[Former Member · Accepted solution]

You can try this Solution

Go to transaction SE38,

RS_TRANSTRU_ACTIVATE_ALL and click on execute .

Give your source system and Infosource name and click on execute .

Then load data again and see.

Edited by: Amrita ka on Mar 30, 2009 4:33 PM

[Former Member · Accepted solution]

Goto RSA5 >Select your DS>Click on Transfer datasources. This will Activate your DS,

Now Replicate DS to BW , activate transfer rules.Now trigger your load.

[Former Member]

Dear All,

My error got resolved now.

Actual problem i had was after source system refresh ,my process chain in BW system got failed as mentioned early.

I did all regular activity which should be done after refresh,but still process chain was gettin failed,finally i activated RSDS_DATASOURCE_ACTIVATE_ALL in SE38 which resolved my issue.

Thanks for all your help.Keep in touch.

Thanks.

[Former Member]

Hi,

I think that you might be getting these errors may be because the BW & Source system connection is not proper. Pleasegoto TCODE RSA1 & in source system tab, check if the connection is active.

If it is active, then check if the datasource and infosource for 0MATERIAL_TEXT are connected and transfer rules are active.

Please let me know.

Regards,

Pankaj

[Former Member]

Hi,

Infact i tried all this procedures but still my load getting failed.Replicated datasources also done source system restore.am getting the below error message.

Check Load from InfoSource

Error message from the source system

Diagnosis

An error occurred in the source system.

System Response

Caller 09 contains an error message.

Further analysis:

The error occurred in Service API .

Refer to the error message.

Procedure

How you remove the error depends on the error message.

Note

If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request.

Kindly suggest me.

Thanks

-

[virenp_devi]

Hi,

Your job is failing in R/3 system. Please go to SM37 in R/3 system, put *request Id (from be REQU_) in the job name and search for the logs. It will provide you all the details

Let me know what do you see in logs.

Regards,

Vuiren

[Former Member]

For master data process chain

Check whether the the transfer structure is Activated or not.

For transcation data process chain

ABAP/4 processor: MESSAGE_TYPE_X A 00 671

1)Check for previous logs, some time though the PC has completed successfully log remains in Yellow! which leads to a short dump.

(Or)

May be the last run was not get completed,and the job will be running from long time i.e PC might got stuck some where for any reason, cancel such long running jobs(SM37)

Edited by: YJV on Mar 30, 2009 12:03 PM