cancel
Showing results for 
Search instead for 
Did you mean: 

Early Watch Report not generated after Solution Manager Upgrade to EHP1 SPS

Former Member
0 Kudos

Hi,

We have upgraded our Solution Manager to EHP1 SPS06.After upgrade Early

Watch reports are not generated.I have cheked job SM:EXEC SERVICES &

found its getting cancelled everyday.

Following is the job log.

-


Job started

Step 001 started (program RDSMOPBACK_AUTOSESSIONS_ALL, variant , user

ID SOLMAN_BTC)

MemSize Begin = 796480 Bytes

*******************************

MemSize Begin = 1931568 Bytes

Solution <000000270980000> "EHP4..." is being edited (Operations)

<000000270980000> "EHP4..."(Operations)

"Create_Periodic_Services" uses = 0 bytes

"Create_Periodic_Services" uses = 758 us time

Trying to perform session EA8000000003378

MODEL_KEY: PEC 0020283274 HANDLE: 4 MODEL_MODE: E MODEL_VERSNR 00001

MODEL_CLASS: EWA Data Model

Version A of MultiProvider 0CCMSMTPH does not exist

Job cancelled after system exception ERROR_MESSAGE

Regards

Santosh KU

Accepted Solutions (0)

Answers (4)

Answers (4)

former_member209604
Active Contributor
0 Kudos

>

> Version A of MultiProvider 0CCMSMTPH does not exist

Hi Santosh,

See instructions in:

[SAP Note 1479322 - Version A of MultiProvider 0CCMSMTPH does not exist|http://www.service.sap.com/sap/support/notes/1479322]

Note will be available soon in SAP Support Portal, replication is ongoing.

Best regards,

Ruediger

Former Member
0 Kudos

> Solution <000000270980000> "EHP4..." is being edited (Operations)

If anyone has the solution open in transaction DSWP, then "SM:EXEC SERVICES" the reports are not generated. Silly but true. We used the parameter rdisp/gui_auto_logout to close sessions before the report runs.

Regards,

Sean

former_member209604
Active Contributor
0 Kudos

>

>

> job SM:EXEC SERVICES

> Version A of MultiProvider 0CCMSMTPH does not exist

> Job cancelled after system exception ERROR_MESSAGE

To solve the issue, please follow the instructions in

[SAP Note 1342231 - ST: Manual actvtn. of BI Content for E2E diagnostics SP18 # 22 (23)|http://service.sap.com/sap/support/notes/1342231]

(The note is also valid for SP23, the translation from DE -> EN is not yet updated.)

Regards,

Ruediger

0 Kudos

Hi Santosh,

Please try this,

1) Please try to reset the session "EA8000000003378" via transaction DSA-> Right mouse click on the session panel and choose Reset.

After that the SM:EXEC SERVICES job should run fine.

When you reseted the sessions via DSA it had no effect on the EWA processing and the dump still occurs.

2) Could you please try to move those sessions to archive?

For more details to archive please see the attached SAP Note 546685.

3) Perhaps the problem is related to the old service definitions on your system. Would you please try to refresh them as per follownig note:

SAP Note 727998 - Complete Replacement of Service Definitions for SDCC/SDCCN.

Hope this helps.

Thanks,

Raghavendra.

former_member209604
Active Contributor
0 Kudos

>

> 1) Please try to reset the session "EA8000000003378" via transaction DSA-> Right mouse click on the session panel and choose Reset.

> After that the SM:EXEC SERVICES job should run fine.

> When you reseted the sessions via DSA it had no effect on the EWA processing and the dump still occurs.

> 2) Could you please try to move those sessions to archive?

> For more details to archive please see the attached SAP Note 546685.

> 3) Perhaps the problem is related to the old service definitions on your system. Would you please try to refresh them as per follownig note:

> SAP Note 727998 - Complete Replacement of Service Definitions for SDCC/SDCCN.

The above recommendation will not help for the reported problem. Don't waste your time.

As a first hint.

In similar cases, it was recommended to proceed as describe in SAP Note 1119766.

I have already informed SAP develoment to provide instructions (which can be found via Note search).

Best regards,

Ruediger