Number range assignment for series group

[former_member216789]

Dear gurus,

I am very new in sap mm, but i have one problem regarding subcon challan creation. when i am going to create it will give me error messge i.e. number range is not maintained for series group.

        when i follow the bellow steps i am unable to assign number range for series group

1) Go to SNUM tcode

2) Then select J1I57FC object

3) Then click on ranges button

4) Then enter series group

5) and then creating intervals from 01 to 9999

6) and also maintained subcontracting attributes as per SCN suggestion.

still error exist!!! is there any missing ? please suggest me asap.

[former_member216789]

Dear Shiva,

Please tell me the exact procedure to check J_1IEXCHDR table.

[Former Member]

Hi

Check it like shown below

[former_member216789]

Dear Shiva,

Please tell me how to reach that screen????? any tcode or path

[Lakshmipathi]

I have already asked you to check in NRIV table and am not sure, whether you have checked there or not.  Alternatively, you can check in SE16 also where you input the table J-1IEXCHDR and further maintain 57FC in Excise TT and execute.

G. Lakshmipathi

[former_member216789]

Dear sir,

Previous issue is resolved as per your all gurus suggestions but not completely...

Now when i am going to post subcon challan it will give me error

Deficit of  1.0000000000000000E+01 in RG23ABED mess no 81259

I have maintain debit and credit a/c for excise TT

57FC 01         CR     RG23AT1

57FC 01         CR     RG23BED

57FC 01         CR     RG23ECS

57FC 01         DR     CLEAR

is there anything missing..

[binoy_vargis1]

Hi,

Also maintain accounts for 57CM and 57NR with subtransaction type 01.

Regards

Binoy     

[former_member216789]

Hiii Mukesh,

When i am going to create same no. range again it will show me 'Transport number range intervals' window which is a big message and then save it successfully. but when again i am going to view my no range it could be blank. there is no num range.

[former_member216789]

Thanks to all repliers,

But whatever you all have suggested i have already gone through it. but still issue is not resolved.

My actually problem is that when i am going to maintain number range for series group its fine. but when i am going to click on display interval button it can not show me defined no. range. and if i again going to maintain no range with same interval it will allow me. then what about my previously maintained no range.

[Former Member]

Hi,

what message you are getting after saving new number range ?

[Former Member]

Hi,

You can check in J_1IEXCHDR table by passing Excise TT and Year you can see pervious number range,

and also i can notice that your number is not saving please check it. i to faced same problem.

Regards

shiva

[Former Member]

HI,

check the number range assigned for the year, object J_1ICHLNNO and J_1I57FC in J1I9 .

Regards,

mukesh

[binoy_vargis1]

Hi Sanjay,

Please check which is the series group assigned in SPRO-->Logistics-General-->Tax on Goods movements-->India-->Business transactions-->Subcontracting-->Subcontracting attributes

Then go to SNRO and give number range to object J_1I57FC.

Regards

Binoy

[phanikumar_v3]

What was the series  group in subcontracting-challan??

Are you maintaining number range for the relevant series group???

Note: whenever you are getting any number range related issue in CIN .

1.just go to SNUM

2.Give j_1i* and press F4 here.

3.See to it for all the necessary objects you need to maintain Number ranges.

Hope this helps.

Note: Please google before opening--you will have ready made answers.

Phanikumar

[Lakshmipathi]

Were you able to see that number range in NRIV table?  Also have a look at this thread where the same issue has been discussed

G. Lakshmipathi