on 05-05-2015 6:46 AM
Hello All,
I am integrating TM and ERP with SAP PI 7.4 dual stack. I have downloaded the SAP TM XI Content version SAPTM 1.10. I have created the Configuration Scenario in Integration Builder and I have generated Sender / Receiver Agreement, Receiver & Interface Determination. But when activating the Receiver Determination I am getting error that some particular Service Interface is missing.
Kindly guide me and give your suggestion.
Regards
Amar..
hi,
how to solve this issue?
i face same error.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
For TM - ERP Integration.
TM services are put into XI Content SAPTM.
While ERP services are from different XI Content. E.G for OrderIntegration, you can find the service XI content ESA ECC-SE. And for Shipment Integration, the service is from XI Content SAP APPL.
Please review the missing services in your case and import the proper XI Content objects.
TM Content
ERP Content
And regarding how to check XI content version, you need to logon you SAP end system and check the software component and its version.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Amarnath
Most probably its an issue with SWCV not populated correctly in ICO after you have run the wizard for apply model from ESR. Make sure the version SAP TM 1.20 APPL 6.05 etc of imported SWCV and interface match because similar interface will be there in 1.1 component as well but not referenced correctly and also check if its according to the configuration guide.
Eventually you might see another type of errors where in the sender system (SAP TM or SAP ERP), there will be some interfaces in error in SXMB_MONI due to the reason that binding not found.
If you look up , those interfaces will not be part of standard content for TM integration . They are supposed to fail , to stop those errors please look at the below thread which talks about BADI extension and table entry correction to stop generation of such messages in the source system.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Sinivas,
SAP TM 1.20 contains below contents only,
But Sender Interface and Receiver Interface is pointing to http://sap.com/xi/APPL/Global2. I am using SAP TM content for SP 6. Please give some clarification and help me out of this.
Regards
Amarnath..
Hello Praveen
I can activate the Objects. The screenshot has
Receiver Interface: TransportationOrderSUITEInvoicingPreparationRequest_In
Namespace: http://sap.com/xi/APPL/Global2
this namespace is missing in the SAP TM Content 1.20 what imported in ESR and getting warning during the object activation.
Will this warning make any impact for the end to end scenario?
And also I am in oscillation whether I have downloaded the exact SAP TM content or not?
Regards
Amar..
Hi Amarnath,
The screenshot suggests there is no mapping involved.
So i would suggest there is some problem with the content download. There must be some mapping involved unless the source and target is going to be same.
Please check if there are more than one versions of the SAP TMS content available. In that case please install all the versions.
And then probably you can activate.
hope that helps,
thanks and regards,
Praveen T
Hi Amarnath,
My few cents:
1. Check if your downloaded content is having Mappings / Process Integration Scenario models
2. Verify what is the Source & Receiver component it refers to in Integration Model
3. AFAIK - http://sap.com/xi/APPL/Global2 would refers to namespace in ECC/ERP software component.
4. Check if you have also downloaded/ Imported corresponding SWCV component for ECC.
Hope it helps
Regards,
Azhar
Hi Azhar
1. Downloaded content having mapping under namespace http://sap.com/xi/TMS/Global/IC
4. Business scenario in ERP has been activated.
What I did in PI is, I just imported the content in ESR and created Configuration Scenario in ID for Invoice Integration Interface.
Regards
Amar..
Hi Amar,
Please provide details of the SWCV downloaded. Also confirm if thats the latest one. Ensure u do a config check and see all references are fine.
Regards,
Sriram
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Sriram,
Have downloaded the XI Content SAPTM 1.20 and it holds the following details,
But when doing the Configuration Scenario in ID part, I am generating the Receiver Determination and Interface Determination automatically thru Model Configurator. After generating the both, Interfaces are pointing to Namespace http://sap.com/xi/APPL/Global2.
But this namespace is missing in the SAP TM XI Content. Please suggest and guide me. What is the exact XI Content I need to download?
Regards
Amar..
Hello all,
Please give me suggestions or some valid inputs. Now I have downloaded the latest SAP TM Content SAP TM 1.20 version. But still getting the same error like Some Service Interface Objects are missing.
Regards
Amar..
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
87 | |
10 | |
10 | |
9 | |
6 | |
6 | |
6 | |
5 | |
4 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.