on 12-09-2015 6:39 AM
Hi Experts,
We are currently using PI 7.31 SP11 single stack. Scenario is simple File to IDoc . The message processed successfully in PI but IDoc are with status 56. In we20 of Receiver R3 system under outbound parameters I could see Receiver port , Partner No. but here since Inbound scenario what values need to hardcoded to the SNDPOR,SNDPRN, SNDRT & RCVPOR, RCVPRN fields in control record field EDI_DC40 ? now I mapped constant 1 to all SNDPOR,SNDPRN, SNDRT but RCVPOR, RCVPRN as values in Receiver port as shown in first screen shot below. Done settings in we21, bd54. But still IDoc is in status 56 . In we19 when I press Start Inbound then it shows below screen but whereas profile maintained already in we 20 of receiver ECC system.
I maintained only port in we21 with T type destination that contains same program ID & PO host and gateway details. Kindly guide on settings to ber maintained Inbound IDoc configuration scenario.
Thnx,Nithin.
Hi Mudassir,
Thanks for reply! No sender port exist so I need to create port in we21 while creating that what type of destination like 3,G,H,T etc should be assigned to that port and & also the user used in that destination should have have what roles? also what type of destination should be assigned to the receiver port & user roles required in that destination? . To map the constant value to SNDPRN should I create logical system in BD64 and assign the same name? for RCVPRN I will assign the logical system name as constant while mapping.
Thnx,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi All,
Suppose I have imported the DESADV.DELVRY05.ZDESADV which is extended IDoc from R3 system and it is CSV to IDoc scenario. So what constant values to be mapped to IDOCTYP [XPath:/DELVRY07/IDOC/EDI_DC40/IDOCTYP] & MESTYP [XPath: /DELVRY07/IDOC/EDI_DC40/IDOCTYP] .
Also what constant value needs to be mapped to CIMTYP [/DELVRY07/IDOC/EDI_DC40/CIMTYP] ?
What is IDoc and Message type here?
Thanks,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Mudassir,
Pls read all of my questions completely and answer each of them kindly
I thought of re-creating both sender & receiver port again so should I create in ECC only ? you mean for both of the port creations I have to use two T type destinations or can I use the same one those created in ECC ? if two different T type destinations in ECC for both sender and receiver port then should I create two destinations in NWA of PO?
Thnx,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Have you worked on PI 7.31 single stack or IDoc_AAE adapter. Pls go through my entire post, it's new ECC system so only one port existing in we21 and should I create port for PI also in we21 of ECC you mean and what parameter indicates is the logical name in we20 ?
Thnx,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Mani,
Thank u for reply, can you pls guide on how to create the port and partner in single stack of PI. If there is some prob in PI then the msg should have been failed in PI only right.
Thnx,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Mudassir,
Thank u for reply! Hope u knew that I am using single stack. Where did you create port SAP POD and SAPPRN as HRACCESS? or what is the source for those values. You mean I have to create ports for both PI & ECC system in WE21 like SAPxxx where xxx is sys ID? Kindly guide.
Thnx,Nithin.
Hello Nitin ,
If your IDoc is failing with status 56 then please check WE57 tcode in ECC to find out whether your idoc type/message type is linked to the function module or not.
Adding the linking might solve your problem.
Thanks.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Raghu,
When I enable that "Apply Control Records from Payload" it failed in PI with Recipient Partner Type is not available but when I disabled that it processed in PI but in receiver ECC system with status 56. As said above I mapped SNDPOR, SNDPRN , SNDPRT with constant value "1" whereas the RCVPOR with receiver port value under outbound parameters in we20 and RCVPRN with Partner No. in we20 . Hence, guide me on settings to be made in ECC system especially partner profile part. in we20.
Thnx,Nithin.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
89 | |
10 | |
9 | |
9 | |
9 | |
6 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.